Metallised Film Manufacturer Polypropylene Cast Film One Side Heat Sealable, Other Side
Corona Treated
| Parameters | Method | Unit | Ref. | Typical Values | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Thickness | Internal | Micron | 18 | 20 | 22 | 25 | 30 | 35 | 40 | |
| Unit Weight | Internal | g/m² | 16.38 | 18.20 | 20.02 | 22.75 | 27.30 | 31.85 | 36.4 | |
| Yield | Internal | m²/kg | 61 | 55 | 50 | 44 | 36.6 | 31.85 | 27.5 | |
| Tensile strength | ASTM D882 | Kg/cm2 | MD | 600 | 550 | 500 | 450 | 400 | 350 | 300 |
| TD | 250 | 250 | 250 | 250 | 200 | 200 | 200 | |||
| Elongation | ASTM D882 | % | MD | 250 | 250 | 250 | 300 | 350 | 400 | 400 |
| TD | 350 | 400 | 400 | 450 | 500 | 500 | 600 | |||
| Seal strength 130˚C, 30psi, 1 sec | Internal | g/25mm | 1400 | 1500 | 1600 | 1800 | 2000 | 2100 | 2500 | |
| Wetting tension | ASTM D2578 | dyne/cm | 38 | |||||||
| Optical density | Internal | % | 2.0 | |||||||
| Coefficient of fraction | ASTM D1894 | UT/M | 0.40 | |||||||
| UT/UT | 0.70 | |||||||||
| Seal initial temp. | Internal | ˚C | 95 – 120 | |||||||
| WVTR | ASTM D3985 | cc/m²/24hr | ˂1 | |||||||
| OTR | ASTM D1249 | g/m²/24hr | ˂150 | |||||||
Can be change as per customer requirements.
The material to be stored in a dry place and at a temperature below 30˚C .after using, if there will any leftover roll then that should be wrapped properly during storage, handling to be done with care to be avoid damages.
The film obeys with FDA regulations.
Treatment value of CPP film treads to decay over a period of time during transportation & storage condition. Therefore it is recommended that the customer should check the treatment levels prior to processing and if a reduction is observed then Information in this publication is believed to be accurate faith and is given in good but it is for the customer to satisfy for its own particular purpose. Accordingly Technovaa plastics industries Pvt. Ltd. given on warranty as to the fitness of the product for any particular warranty purpose and implied or condition. Technovaa plastics industries Pvt. Ltd. reserves the right to change the technical data sheet at any time without information.
| CODE | DESCRIPTION |
|---|---|
| SSMF | Normal metallized cast film |
| HIMB | High bond metallized cast film |
| EXMB | Extrusion grade metallized cast film (excellent metal bond) |
| ISMF | Improve seal metallized cast film |
| ISMB | Improve seal with high bond metallized cast film |
| LSMF | Low SIT metallized cast film |
| LSMB | Low SIT with high metal bond metallized cast film |
| LSSB | Low SIT high bond with high speed metallized cast film |
| LSHS | Low SIT with high speed metallized cast film |
| USMF | Ultra low SIT metallized cast film |
| USMB | Ultra low SIT with high metal bond metallized cast film |
| USSB | Ultra low SIT high speed with high metal bond cast film |
| HSMB | High speed with high metal bond metallized cast film |
| HSMF | High speed metallized cast film |
